features bushing mount optional ar pin feature plastic or metal shaft and bushings wirewound solder lugs or pc pins sealable (full body seal) designed for use in hmi applications rohs compliant* 3590 - precision potentiometer speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. *rohs directive 2002/95/ec jan. 27, 2003 including annex and rohs recast 2011/65/eu june 8, 2011. electrical characteristics 1 standard resistance range...................................................................................................... .................................................................. 200 to 100 k ohms total resistance tolerance ............................................................................................................................... ................................................................. ? % independent linearity ......................................................................................................... .......................................................................................... ?.25 % effective electrical angle .................................................................................................... ............................................................................3600 ?+10 ? -0 ? absolute minimum resistance ................................................................................................... ...................1 ohm or 0.1 % maximum (whichever is greater) noise ......................................................................................................................... ....................................................................... 100 ohms enr maximum dielectric withstanding voltage (mil-std-202, method 301) sea level .................................................................................................................... ...........................................................................1,500 vac minimum power rating (voltage limited by power dissipation or 450 vac, whichever is less) +40 ? ............................................................................................................................... ..........................................................................................2 watts +125 ? ............................................................................................................................... ..........................................................................................0 watt insulation resistance (500 vdc) ............................................................................................... ...................................................... 1,000 megohms minimum resolution..................................................................................................................... .........................................................see recommended part numbers environmental characteristics 1 operating temperature range ................................................................................................... ................................................................... -40 ? to +125 ? storage temperature range ..................................................................................................... .................................................................... -55 ? to +125 ? temperature coef cient over storage temperature range 2 .........................................................................................................?0 ppm/? maximum/un it vibration ..................................................................................................................... ........................................................................................................15 g wiper bounce ................................................................................................................. ...............................................................0.1 millisecond maximum shock.......................................................................................................................... ........................................................................................................50 g wiper bounce ................................................................................................................. ...............................................................0.1 millisecond maximum load life ..................................................................................................................... ...............................................................................1,000 hours, 2 watts total resistance shift ....................................................................................................... .............................................................................? % maximum rotational life (no load)...................................................................................................... .......................................................... 1,000,000 shaft revolutions total resistance shift ....................................................................................................... .............................................................................? % maximum moisture resistance (mil-std-202, method 103, condition b) total resistance shift ....................................................................................................... .............................................................................? % maximum ip rating sealed versions (-3, -4, -7, and -8) ......................................................................................... ...................................................................................... ip 65 unsealed versions (-1 -2, -5, and -6) ........................................................................................ .................................................................................... ip 40 mechanical characteristics 1 stop strength.................................................................................................................. ............................................................ 45 n-cm (64 oz.-in.) minimum mechanical angle .............................................................................................................. .............................................................................3600 ?+10 ? -0 torque (starting & running) ................................................................................................... ............................. 0.35 n-cm (0.5 oz.-in.) maximum (unsealed) 1.1 n-cm (1.5 oz.-in.) maximum (sealed) mounting ..................................................................................................................... .........................................................55-80 n-cm (5-7 lb.-in.) (plastic) 90-113 n-cm (8-10 in.-lb.) (metal) shaft runout................................................................................................................... ...................................................................0.13 mm (0.005 in.) t.i.r. lateral runout ................................................................................................................ ...................................................................0.20 mm (0.008 in.) t.i.r. shaft end play ................................................................................................................ ...................................................................0.25 mm (0.010 in.) t.i.r. shaft radial play ............................................................................................................. ..................................................................0.13 mm (0.005 in.) t.i.r. pilot diameter runout ......................................................................................................... ..............................................................0.08 mm (0.003 in.) t.i.r. backlash ...................................................................................................................... ...................................................................................... 1.0 ?maximum weight ........................................................................................................................ ................................................................................approximately 19 g terminals ..................................................................................................................... ...........................................................................solder lugs or pc pins soldering condition manual soldering........................................................... 96.5sn/3.0ag/0.5cu solid wire or no-clean rosin cored wire; 370 ? (700 ?) max. for 3 seconds wave soldering ...................................................................................96.5sn/3.0ag/0.5cu solder wi th no-clean ux; 260 ? (500 ?) max. for 5 seconds wash processes ............................................................................................................... ........................................................................not recommended marking ..................................... manufacturer? name and part number, resistance value and tolerance, linearity tol erance, wiring diagram, and date code. ganging (multiple section potentiometers) ..................................................................................... ................................................................. 1 cup maximum hardware ............................................................................................................ one lockwa sher and one mounting nut is shipped with each potentiometer. note: for anti-rotation pin add 91 after con guration dash number. example: -2 becomes -291 to add ar pin. 1 at room ambient: +25 ? nominal and 50 % relative humidity nominal, except as noted. 2 consult manufacturer for complete speci cation details for resistances below 1k ohms. boldface listings are in stock and readily available through distribution. for other options consult factory. rohs identifier: l = compliant recommended part numbers (printed circuit) (solder lug) (solder lug) resistance ( ) resolution (%) 3590P-2-102L 3590s-2-102l 3590s-1-102l 1,000 .029 3590p-2-202l 3590s-2-202l 3590s-1-202l 2,000 .023 3590p-2-502l 3590s-2-502l 3590s-1-502l 5,000 .025 3590p-2-103l 3590s-2-103l 3590s-1-103l 10,000 .020 3590p-2-203l 3590s-2-203l 3590s-1-203l 20,000 .019 3590p-2-503l 3590s-2-503l 3590s-1-503l 50,000 .013 3590p-2-104l 3590s-2-104l 3590s-1-104l 100,000 .009 *rohs compliant
12.19 ?0.51 (.480 ?.020) solder lug terminal pc pin terminal thickness 1.63 ?0.38 (.064 ?.015) .305 ?.003 (.012 ?.0001) 0.86 (.034) 3 plcs. 3.30 ?0.38 (.130 ?.015) 2.54 (.100) 3 plcs. 12.19 ?0.51 (.480 ?.020) 3590 - precision potentiometer panel thickness dimensions (for bushing mount only) panel pot lockwasher hex nut 2.46 - 3.81 (.097 - .150) 1.60 +.08/-.03 (.063 +.003/-.001) 10.44 ?.07 (.411 ?.003) dia. dia. additional hole for anti-rotation pin anti-rotation pin hole is shown at six o'clock position for reference only. the actual location is determined by the customer's application. refer to the front view of the potentiometer to see the location of the optional a/r pin. panel thickness and hole diameters are recommended for best fit. however, customers may adjust the dimensions to suit their specific application. 7.42 (.292) r product dimensions speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. rev. 06/12 2 1 3 bushing diameter (see part numbers) shaft diameter (see part numbers) 12.70 (.500) mounting surface 15.54 (.612) 5.08 .38 (.200 .015) 6.99 .38 (.275 .015) 5.08 .38 (.200 .015) 10.31 + .00/- .13 (.406+.000/-.005) .25 (.010) 1.19 (.047) 7.92 (.312) .81 (.032) 20.62 .81 (.812 .032) 18.6 .4 (.732 .015) 12.2 (.48) 11.81 (.465) dia. 22.22 .38 (.875 .015) dia. r max. 12.70 0.25 (.500 .010) mounting surface 15.54 (.612) 12.2 (.480) 11.81 (.465) dia. 22.22 .38 (.875 .015) dia. r max. 2 3 1 bushing dia. (see part numbers) 3/8-32 unef .76 .25 .030 .010 shaft dia. (see part numbers) 5.08 .38 (.200 .015) 6.99 .38 (.275 .015) 10.31 +.00/-.10 (.406 +.000/-.004) r 5.08 .38 (.200 .015) .25 (.010) 7.93 (.312) .81 (.032) 20.63 .81 (.812 .032) .81 .25 (.032 .010) 18.59 .38 (.732 .015) -2, -4, -6, -8 con gurations -1, -3, -5, -7 con gurations recommended pcb layout fms hole diameter 2.08 (.082) 5.08 (.200) 5.08 (.200) 6.99 (.275) schematic 13 ccw cw cw 2 tolerances: except where noted .508 .127 decimals: .xx (.02), .xxx (.005) fractions: 1/64 mm dimensions: (in.) shaft & bushing con gurations (bush ing - dxl, shaft - d): (-1) plastic bushing (3/8 ?x 5/16 ? and shaft (.2480 + .001, - .002) (-2) metal bushing (3/8 ?x 5/16 ? and shaft (.2497 + .0000, - .0009) (-3) sealed, plastic bushing (3/8 ?x 5/16 ? and shaft (.2480 + .001, - .002) (-4) sealed, metal bushing (3/8 ?x 5/16 ? and shaft (.2497 + .0000, - .0009) (-5) metric, plastic bushing (9 mm x 7.94 mm) and shaft (6 mm + 0, - .076 mm) (-6) metric, metal bushing (9 mm x 7.94 mm) and shaft (6 mm + 0, - .023 mm) (-7) metric, sealed, plastic bushing (9 mm x 7.94 mm) and shaft (6 mm + 0, - .076 mm) (-8) metric, sealed, metal bushing (9 mm x 7.94 mm) and shaft (6 mm + 0, - .023 mm) terminal styles ??terminal style ??terminal style
|
